Sunday, September 28, 2008



Sorry for the poor start to my blog. From now on I will post new items at least weekly so you aren't left wondering if I will ever give you anything else useful.
As fare as the family is concerned; Chris dresses up for 80's day at school last week. I'd kept some parachute pants and a few shirts from that era so he was able to dress in authentic gear. He was the most 80s kid art school and got extra credit points for dressing up. He is also loving band again this year and is playing on the JV soccer team. This is his first year ever playing soccer and I'm please with his attempt.

I'm getting ready to help teach our next CERT training to the community. It has been a good way to help people help themselves in an emergency and then help their neighbors. If you haven't had the training I highly recommend it. The whole training spun out of the need to insure that when common citizens volunteer to help in a disaster, they can do so safely. It also helps with basic family emergency preparedness and not being a victim in a disaster.
Yesterday, while I was playing with Micah; rolling truck down out driveway he asked me, "Do you remembered the man at church who has no arm?" I said yes and he asked a lot of questions about how and why he lost it. Finally he said, "Someday I'll fix his arm for him." He was totally serious.

Becky and I just recently went to see Sinbad as a date. The tickets were a gift from my boss and his wife for my birthday. We about died laughing. Sinbad is only 3 years older than me and did his spiel from theage angle. We were serious hurting when the show was done. It was a great time!
Posted by at 1 comment:
Labels:

Monday, June 30, 2008

By Way of Introduction

I am officially entering the world of blogging. Partly because of seeing my wife and friends enjoying it so much, partly because I always have something to say or share (some of which may even be of value to someone else); and partly to help add a few positive bits to the Internet that may offset the filthy or bad things roaming it's pathways. Since my wife's blog http://www.petersonputterings.blogspot.com/ shares some of the latest things about our family I plan to go beyond just our family and share other things I enjoy.

The key items I will share in the blog are a mixed bag of things related to autobody repair and fabrication, my family, my church, Boy Scouting. I hope you enjoy your visits and share your thoughts and experiences with me and others.
~Lance
Posted by at No comments:

Three Loves - Work, Family, & Motorcyles



Although this is an old photo, I thought I'd start out with it. It showcases my two loves; my family and my work.

I get paid to play! Working in Prototype Fabrication for Honda has been a great adventure, but not nearly as great an adventure as raising a family along with my wonderful wife, Becky.

Christopher, our oldest son, is just about to start driving. Both fear and excitement war in my heart for him; and for those others on the road with him. Last fall, he traded his '02 XR70 for a Honda'69 SL 90 (like the first bike I had as a youth). We've been buying better parts for it trought the winter and spring. He got it torn down and was ready to repaint the frame. Then, this last week a friend gave me a '78 Honda CM185 Twinstar. It is a bit rusty from sitting and has some carb issues, but is definitely fixable. Chris asked me to trade him bikes; so I now have my first bike and he is beginning restoring the Twinstar to hopefully drive back and forth to school after he gets his license. He really loves the look of that old bike! we'll keep you posted on his progress.

Micah is now 3 and a half and still a massive daddy's boy. From less than year old he has been enamoured with vehicles of all types, especially trucks, aircraft, and motorcycles.

He loves riding around the yard on my FJ1200 when I move it for painting something in the garage. He was really upset when Chris traded his XR70 and he lost his normal 'ride'.

Becky on the other hand, seldom gets on a bike, but has been very supportive of our motorcycle interests. It helps that I am very committed to safe riding practices and wearing all the gear when on the road or doing more than riding around the house.
Posted by at No comments:
Subscribe to: Posts (Atom)

Fabrication 101

So, you want to do your own bodywork?
(Part 1 – Starter tools)

It is possible to do your own bodywork - but, recognize that you will need to spend a little on the basic tools to even make it worthwhile. Other tools make it easier, but are more expensive and can sometimes be borrowed or rented. My grandfather, Coy Lee, had a good philosophy when it comes to deciding whether to borrow or purchase a tool. “If you use it more than twice a year, consider buying it.” I would amend his rule slightly to say then “If it costs less than $200 and you use it more than twice a year - buy it.” If it is between $200 – 500 borrow or rent it the first year or two, then buy it since it is obvious you plan on using it on more than just your original “fixer-upper”.

After having said all that, what are the bare necessities of bodywork tools? Assuming you are not going to tackle any sheet straightening bigger than small door dings or dents and creases in areas where you can readily reach the back side and beat with a hammer; here is the bare-bones list of tools.

> A body hammer and dolly set with 3 hammers: wedge, pick, and shrinking. Cheap sets typically are just as good as expensive ones. Except for the shrinking hammer, which should be flat, the hammer heads should have a slight crown to them.
> One or two small palm sixed sanding blocks . They should be stiff but slightly flexible.
> One twelve inch sanding block. It Should be stiff but flexible – I was taught to tape 3 paint mixing stick together – it will do in a pinch.
> A package of plastic putty spreaders. Typically yellow polyethylene plastic for easy cleaning.
> A six inch disk action (DA) sander. A cheap model will usually cost under $60 dollars and do fine for starters
> One or two Body putty files. Often nicknamed “cheese graters”.
> One air blow gun.
A cheap pistol type grinder for paint removal. Also usually under $60.
> A cheap paint gun. Don’t spend more than $100 – the cheap knockoffs often work just as well as the $500 guns and will do even after you decide how committed you are to future paint work.
> A small air compressor. This will be your most expensive purchase would best have a two stage pump for fast recovery when running your air tools. It can still be 100V, but 220 V units are typically stronger and longer lasting. It should put out 115 cfm of higher apir pressure. Don’t spend more than $500 on one. You can always go for a bigger unit latter, if you choose to really get into bodywork.
> A tight fitting respirator for painting. I recommend the Survivair brand, but others are just as good. Make sure the vendor teaches you how to properly fit it to your face.
> Loose fitting paper “dust nuisance” masks. For use while sanding. Buy a box – they are cheap and can be used for home repair and other uses.
> Sandpaper for hand and block sanding and use on your DA. I recommend paper in grits, 36, 80, 1880, 240, and 320. You should buy 6” DA and rolls in all the suggested grits. I recommend rolls rather than sheets because they come in widths to fit standard sanding blocs and work well for hand sanding. Sheet paper is always to big and requires a lot of cutting or tearing down to size.
> Safety glasses or goggles. You won’t be doing body work for long if you end up with metal shavings in your eye.
With this basic setup you can do light body work like door dings and things not requiring dent pulling or cut–and-replace welding. You will also need some consumables like paper shop towels, nitride gloves, paint sticks, paint strainers, etc. I’ll go into more detail as we go through each repair step in future articles. You total starting investment will be from $500 - $800, so buy it piece at a time as you can afford it. Buy the compressor last; you could even rent one for your first job just in case it turns out to be your only job.
Why do I say that? Bodywork, while very rewarding when finished, is a lot of hard work and, unlike mechanical work, the sanding part is a bit monotonous. Body shaping also takes developing a good “feel” literally to insure that the panel is straight.
In my next article I’ll start you through the body repair process. Along the way I’ll give you tips and suggest more expensive but time saving tools you can add to your box, if you decide you will do more vehicles in the future. Until then, get shopping.

~lp Sept 2008

E-mail me and I can send you a PDF copy of any of these past articles:
> POR 15: Rust Solution (Article 1)

My Blog Stats


View My Stats
Powered By Blogger